Planet Technology Switch POE 152 User Manual

IEEE 802.3af  
Power over Ethernet Injector  
POE-152  
User’s Manual  
- 1 -  
 
TABLE OF CONTENTS  
1. INTRODUCTION.......................................................................................................................................... 4  
1.1 CHECKLIST ................................................................................................................................................ 4  
1.2 ABOUT THE POWER OVER ETHERNET INJECTOR .......................................................................................... 4  
1.3 FEATURES ................................................................................................................................................. 4  
1.4 SPECIFICATION .......................................................................................................................................... 5  
1.5 PRODUCT OUTLOOK................................................................................................................................... 5  
2. HARDWARE INSTALLATION..................................................................................................................... 6  
2.1 BEFORE INSTALLATION............................................................................................................................... 6  
2.2 POE-152, THE INJECTOR INSTALLATION...................................................................................................... 7  
2.3 POE-152 AND POE-152S, THE IEEE 802.3AF INJECTOR AND SPLITTER INSTALLATION................................ 7  
2.4 CONNECT WITH IEEE 802.3AF DEVICES...................................................................................................... 8  
3.TROUBLESHOOTING................................................................................................................................... 9  
APPENDIX A NETWORKING CONNECTION ............................................................................................... 10  
A.1 SWITCHS RJ-45 PIN ASSIGNMENTS......................................................................................................... 10  
A.2 RJ-45 CABLE PIN ASSIGNMENT................................................................................................................. 10  
- 3 -  
 
1. INTRODUCTION  
1.1 Checklist  
Thank you for purchasing our POE-152 IEEE 802.3af Power over Ethernet Injector, your Power over Ethernet  
Injector package shall contains following contents:  
Check the contents of your package for following parts:  
ò
ò
ò
ò
Power over Ethernet Injector x1  
User's manual CD x1  
Power Adapter x1  
Power cord x 1  
If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton  
including the original packing material, and use them against to repack the product in case there is a need to return it to  
us for repair.  
1.2 About the Power over Ethernet Injector  
The POE-152 is an IEEE 802.3af Power over Ethernet Injector that provides DC 48V over Ethernet cables. The POE-152  
IEEE 802.3af Power over Ethernet Injector inserts DC Voltage into Cat.5 cable, allowing the cable between the Injector  
(POE-152) and Splitter (POE-152S-5V/12V) to transfer data and power simultaneously. The maximum distance between  
the Injector (POE-152) and Splitter (POE-152S-5V/12V) is 100 meters. With POE-152 being installed, it combines the  
Ethernet digital data with power over the twisted pair cables as an IEEE 802.3af Power over Ethernet Injector. And the  
IEEE 802.3af Power over Ethernet splitter shall separate the digital data and the power into two outputs.  
Unlike existing Power over Ethernet Injector, except the 10/100Mbps Fast Ethernet connection ability, the POE-152 also  
provide 1000Mbps Gigabit Ethernet connection ability.  
With IEEE 802.3af Power over Ethernet devices being installed, the system administrator only has to use a single RJ-45  
Ethernet cable to carry both power and data to each device. Besides, to connect through POE-152 and  
POE-152S-5V/12V, you could also have benefits including cost saving, easy for networking planning and higher reli-  
ability. What’s more, upon any IEEE 802.3af devices being installed, the POE-152 or together with POE-152S-5V/12V  
can make the connection while migrating or splitting the power and the Ethernet digital packets, such as connecting the  
POE-152 to an IEEE 802.3af complied devices, AP or IP phone.  
1.3 Features  
Complies with IEEE 802.3af Power over Ethernet, IEEE 802.3/802.3u /802.3ab 10/100/1000Base-T  
Provides DC 48V power over RJ-45 Ethernet cable to device with Ethernet port  
LED indicators power input indication  
Distance up to 100 meters  
Auto-detect of POE IEEE 802.3af equipment, protect devices from being damaged by incorrect installation  
Works with EIA568, category 5, 5e or 6 ,2/4-pair cables for 10Base-T or 100Base-TX and 1000Base-T  
EMI standards complies with FCC, CE class B  
- 4 -  
 
1.4 Specification  
Model  
POE-152  
Ethernet Connector  
2 x RJ-45( 1 for data + DC out, 1 for Data in)  
Ethernet Data rate  
Input voltage  
10/100/1000Mbps( vary on Ethernet device attached)  
DC 48V, 0.4A  
Number of device can be powered  
Ethernet cable  
1
TIA/EIA-568, Category 5/5e/6 cable  
1 x power, 1 x POE ready / in-use  
LED indicator  
Operating environment  
Storage environment  
0~50 Degree C, 5%~90%RH  
-20~70 Degree C, 5%~90%RH  
Dimension (W x D x H)  
Weight  
73 x 55 x 24 mm  
50g  
Emission  
FCC Class B, CE mark  
Standard Compliance  
IEEE 802.3 Ethernet  
IEEE 802.3u Fast Ethernet  
IEEE 802.3ab Gigabit Ethernet  
IEEE 802.3af Power over Ethernet  
1.5 Product Outlook  
LED definition:  
LED  
Color  
Yellow  
Green  
Function  
Power  
Lights to indicate that the POE-152 has power.  
PoE ready / in-use  
Lights to indicate the port is providing 48VDC in-line power.  
- 5 -  
 
2. HARDWARE INSTALLATION  
This product provides three different running speeds – 10Mbps, 100Mbps, 1000Mbps in the same device and auto-  
matically distinguishes the speed of incoming connection.  
This section describes the hardware features of POE-152. Before connecting any network device to the POE-152, read  
this chapter carefully.  
2.1 Before Installation  
Before your installation, it is recommended to check your network environment. If there is any IEEE 802.3af devices need  
to power on, the POE-152 can provide you a way to supply power for this Ethernet device conveniently and easily. The  
POE-152 equips with an AC-DC adapter with DC 48V input and injects, this DC power into the pin of the twisted pair cable  
(pair 1, 2 and pair 3, 6 for Fast Ethernet) and (pair 4, 5 and pair 7, 8 for Gigabit Ethernet).  
If there is very difficult to find a power socket for AC-DC Adapter of your non-IEEE 802.3af networked device, the POE-152  
and POE-152S can provide you a way to supply DC power for this Ethernet device conveniently and easily.  
The10/100/1000Mbps speed duplex mode from Ethernet port of POE-152 depends on which Ethernet device attached.  
@Notice:  
The POE-152 and POE-152S can be installed in pair. However, the use of third-party device is allowed if the device  
complied with IEEE 802.3af standard.  
- 6 -  
 
2.2 POE-152, the Injector installation  
1. Connect a standard network cable from Switch/workstation to “Ethernet” port of POE-152.  
2. Connect the long cable that will be used to connect to the remote device to the port “Ethernet + DC”. The screen in  
Figure 1 appears.  
3. Connect the AC adapter to “DC 48V” of POE-152. The power LED will be steady on.  
Figure 1: the Injector installation  
2.3 POE-152 and POE-152S, the IEEE 802.3af Injector and Splitter installation  
1. Connect a standard network cable from “Ethernet+DC” of POE-152 to “Ethernet+DC” of POE-152S. The POE LED of  
POE-152 / POE-152S will light on continuance. The screen in Figure 2 appears.  
From POE-152 or  
IEEE 802.3af Power  
Supply equipment  
Figure 2: Connection to POE-152S  
2. Connect the UTP cable in the package from “Ethernet” of POE-152S to the RJ-45 port of remote device.  
3. Connect proper DC plug from “DC OUT” of POE-152S to remote device.  
4. Power on the remote device and the LED indicator on POE-152S will remains on, the screen in Figure 3 appears.  
- 7 -  
 
Figure 3: Connection architecture over POE-152/152S  
@Notice:  
1. According to IEEE 802.3af standard, the POE-152 will not inject power to the cable if not connecting to  
IEEE 802.3af devices.  
2. Please ensure the output voltage is correct before applying power to remote device.  
2.4 Connect with IEEE 802.3af devices  
Due to the capability of IEEE 802.3af standard, the POE-152 can directly connect with any IEEE 802.3af end-nodes like  
wireless access point, VoIP phones and Internet camera where support IEEE 802.3af In-line Power over Ethernet port.  
The screen in Figure 4 appears.  
Figure 4: Connection to IEEE 802.3af device  
Once POE-152 detects the existence of an IEEE 802.3af device, the LED indicator will be steady, ON to shows it is  
providing power.  
@Notice:  
If the connected device is not fully complying with IEEE 802.3af standard or in-line power device, the LED indicator of  
POE-152 will not be steady on.  
- 8 -  
 
3.TROUBLESHOOTING  
This chapter contains information to help you solve issues. If the POE-152 is not functioning properly, make sure the  
POE-152 was set up according to instructions in this manual.  
The PoE LED is not lit  
Solution:  
Check the cable connection between POE-152 and IEEE 802.3af device.  
Why I connect my PoE device to POE-152 and it cannot power on?  
Solution:  
1. Please check the cable type of the connection from POE-152 to the other end. The cable should  
be an 8-wire UTP, Category 5/5e/6, EIA568 cable within 100 meters. A cable with only 4-wire,  
short loop or over 100 meters, all will affect the power supply.  
2. Please check and assure the device that fully complied with IEEE 802.3af standard.  
10/100/1000Base-T port link LED is lit, but the traffic is irregular  
Solution:  
Check that the attached device is not set to dedicate full duplex. Some devices use a physical or software switch to  
change duplex modes. Auto-negotiation may not recognize this type of full-duplex setting.  
- 9 -  
 
APPENDIX A NETWORKING CONNECTION  
A.1 Switch‘s RJ-45 Pin Assignments  
1000Mbps, 1000Base T  
Contact  
MDI  
MDI-X  
1
2
3
4
5
6
7
8
BI_DA+  
BI_DA-  
BI_DB+  
BI_DC+  
BI_DC-  
BI_DB-  
BI_DD+  
BI_DD-  
BI_DB+  
BI_DB-  
BI_DA+  
BI_DD+  
BI_DD-  
BI_DA-  
BI_DC+  
BI_DC-  
10/100Mbps, 10/100Base-TX  
RJ-45 Connector pin assignment  
MDI  
MDI-X  
Contact  
Media Dependant  
Interface  
Media Dependant  
Interface -Cross  
1
2
Tx + (transmit)  
Tx - (transmit)  
Rx + (receive)  
Rx + (receive)  
Rx - (receive)  
Tx + (transmit)  
3
4, 5  
6
Not used  
Rx - (receive)  
Tx - (transmit)  
7, 8  
Not used  
A.2 RJ-45 cable pin assignment  
The standard RJ-45 receptacle/connector  
- 10 -  
 
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation  
and color of straight cable and crossover cable connection:  
Figure A-1: Straight-Through and Crossover Cable  
Please make sure your connected cables are with same pin assignment and color as above picture before deploying the  
cables into your network.  
2080-A31120-001  
- 11 -  
 

Philips Cordless Telephone CD1352S User Manual
Philips Range 32PFL7404H User Manual
Planar Personal Computer C3012T User Manual
Polaris Offroad Vehicle 120 Pro X User Manual
Polar Watch AXN300 User Manual
Porter Cable Air Compressor CPF23400P User Manual
Poulan Trimmer 545137277 User Manual
Poulan Trimmer PP136E User Manual
Pride Mobility Mobility Aid JET2 User Manual
PVI Industries Water Heater 1100N300A E User Manual