Pentair Swimming Pool Pump CSP Series User Manual

CSP Series  
Commercial Self-Priming Pump  
Standard Features  
Cast iron construction, enclosed bronze impeller and  
bronze wear rings for long lasting reliability.  
For commercial and public swimming  
pools and spas, aquatic facilities, water  
parks and fountain applications where  
high performance and self-priming  
characteristics are desired.  
Exceptional self priming design with hair and lint  
strainer installed – allows pumps to be installed  
above or below water level.  
Rugged, self-priming CSP Series commercial  
Oversized hair and lint strainer* with electro-polished  
stainless steel basket holds a large quantity of debris.  
pumps feature an enclosed bronze impeller,  
standard 6" x 4" flange connections, plus a  
1,100 cubic inch capacity hair and lint strainer.  
Motors are standard JM type, NEMA “C” flange  
design with a stainless steel shaft sleeve. These  
Available in a wide range of performance levels from  
1
7 ⁄  
2
to 20 HP to handle your varied pumping needs.  
®
Nationally recognized NEMA motors offer high  
performance under continuous operation.  
1
Back pull-out design enables servicing of normal  
wearing parts without disconnecting piping.  
cast iron pumps are available in 7 ⁄2, 10, 15 and  
20 HP, and may be purchased with or without  
corrosion-preventing epoxy coating on all wetted  
surfaces. Pump and strainer sold separately.  
Dimensionally compatible to most installations for  
easier initial hook-ups or retrofits.  
Integral design base is slotted for ease of mounting.  
*To insure priming and proper pump operation, install only with Sta-Rite Hair  
and Lint Strainer. Order pump and strainer separately.  
Pentair Water Commercial Pool and Spa™  
 
CSP Commercial Pump  
1/4 NPT  
PLUG  
19.30  
16.55  
(OPTIONAL  
SUCTION  
GAUGE  
CP  
6",  
125 LB.  
ANSI  
20.27  
LOCATION)  
SUCTION  
FLANGE  
20.32  
1/4 NPT PLUG  
(OPTIONAL PRESSURE  
GAUGE LOCATION)  
3/4 - 10 UNC  
x 1.60 DEEP  
6.88  
11.00  
B
11.62  
FLOW  
5.225  
4.25  
16.38  
1/2 NPT  
DRAIN  
PLUG  
E
3/4 - 10 UNC  
THRU FLANGE  
(6) PLACES  
T
A
8.50  
D
10.45  
6.25  
7.68  
4", 125 LB. ANSI  
DISCHARGE FLANGE  
R
B
9.50 BC  
B
22.5°  
11.00  
1/2 NPT  
3.44  
SLOTS FOR  
5/8" MOUNTING  
BOLTS  
19.48  
DRAIN PLUG  
F
4.06  
7.92  
15.85  
S
9.00  
6.00  
5/8 - 11 UNC x 1.28 DEEP  
(8) PLACES.  
.88 THRU (8) PLACES  
SECTION B - B  
(VOLUTE TOP VIEW)  
Outline Dimensions  
Catalog Number  
All dimensions shown in inches.  
A
B
CP  
D
E
F
G
H
I
CSPHK, CCSPHK  
CSPHK3, CCSPHK3, CSPH2K3  
CSPHL, CCSPHL  
10.62  
9.00  
7.00  
6.75  
8.26  
7.00  
8.50  
8.50  
10.80  
12.44  
39.44  
40.31  
42.69  
41.00  
42.50  
42.50  
46.75  
48.50  
5.25  
4.50  
5.25  
5.25  
5.25  
5.25  
6.25  
6.25  
4.25  
3.75  
4.25  
4.25  
4.25  
4.25  
5.00  
5.00  
5.50  
5.50  
7.00  
5.50  
7.00  
7.00  
8.20  
10.00  
1.00  
1.75  
1.00  
1.00  
1.00  
1.00  
0.00  
0.00  
30.00  
29.13  
30.00  
30.00  
30.00  
30.00  
31.62  
31.65  
8.50  
7.50  
8.50  
8.50  
8.50  
8.50  
10.00  
10.00  
10.35  
10.62  
10.62  
10.62  
12.50  
13.38  
CSPHL3, CCSPHL3  
CSPHM3, CCSPHM3  
CSPH2L3, CSPH2M3  
CSPHN3, CCSPHN3  
CSPH2N3, CCSPH2N3  
Ordering Information  
Catalog  
Number  
Nominal  
HP (kw)  
Motor  
Voltage  
Full-Load*  
Amps  
Approx. Ship. Weight lbs. (kg)  
(Pump Only)  
Phase  
CSPHK/CCSPHK  
7-1/2 (5.6)  
7-1/2 (5.6)  
7-1/2 (5.6)  
10 (7.5)  
1
3
3
1
3
3
3
3
3
3
230  
208-230/460  
200  
39  
270 (122)  
265 (120)  
265 (120)  
275 (124)  
270 (122)  
270 (122)  
280 (127)  
280 (127)  
325 (148)  
350 (159)  
CSPHK3/CCSPHK3  
CSPH2K3/CCSPH2K3  
CSPHL/CCSPHL  
21.7/18.0/9.8  
22.1  
230  
46  
CSPHL3/CCSPHL3  
CSPH2L3/CCSPH2L3  
CSPHM3/CCSPHM3  
CSPH2M3/CCSPH2M3  
CSPHN3/CCSPHN3  
CSPH2N3/CCSPH2N3  
10 (7.5)  
208-230/460  
200  
27.6/25/12.5  
28.1  
10 (7.5)  
15 (11.2)  
15 (11.2)  
20 (15)  
208-230/460  
200  
44.2/40/20  
42.3  
208-230/460  
200  
55.3/50/25  
57.3  
20 (15)  
*Amp draw may vary depending on motor manufacturer.  
OPTIONS: CCSP Models feature special epoxy coated castings for maximum performance and corrosion resistance.  
60 Hz T.E.F.C., 60 Hz premium efficiency, or 575 volt motors available, consult factory.  
NOTE: Maximum ambient temperature for motor is 104°F (40°C). All pump motors require external overload protection (magnetic starter).  
Pump strainer must be ordered separately (see below). Full load amps on motor model plate.  
Accessory Ordering Information  
Catalog  
Number  
Approx. Ship  
Weight lbs. (kg)  
Approx. Ship.  
Vol. Ft3 (m3)  
Description  
PKG 184  
Strainer for CSP/CCSP, 6" ANSI Flange (1,100 cu. in. capacity)  
180 (82)  
180 (82)  
6.4 (.18)  
6.4 (.18)  
PKG 184C Strainer for CSP/CCSP, 6" ANSI Flange (1,100 cu. in. capacity), Epoxy Coated  
PKG 184  
 
CSP Series  
Commercial Self-Priming Pump  
neoprene to protect motor bearings from any seal leakage.  
The pump shall be capable of operating at up to 75 psi, 125°F  
continuous water temperature and within a pH range of 6 to 9.  
ENGINEERING SPECIFICATIONS  
CSP/CCSP Series Pump  
Recirculating pump shall be Sta-Rite Model No. _________  
self-priming centrifugal pump, ____ phase, 60 Hz.  
®
The electric motor coupled to the pump shall be of the NEMA  
series JM construction with carbon steel shaft inside a remov-  
able shaft sleeve of 300 series stainless steel. The motor shall  
be of an open drip-proof design (unless otherwise specified) with  
permanently sealed ball bearings. Motors shall be continuous  
duty rated at 40°C (or better) ambient and be suitable for outdoor  
installation.  
General Notes  
Install pump in a cool, dry, well vented location away from pool  
heaters, and chemical storage.  
Pump should be firmly mounted with pipe supported, to prevent  
vibration and undue operational noise.  
The pump motor shall be a ___ HP, ___ phase, 60 Hz, 3450 RPM  
for service on a ___ volt electric supply. The pump shall be  
rated for ______ GPM at ____ TDH. The pump shall be tested  
and certified by a nationally recognized testing laboratory to  
conform to National Sanitation Foundation Standard 50. (CCSP  
models only.)  
Allow 12" minimum clearance behind motor for servicing.  
Motor overheating may be caused by a voltage drop or excessive  
voltage. Be sure that wire size and voltage input is properly  
regulated.  
Hair and Lint Strainer  
Specifications  
The pump strainer shall consist of a ______ (red brass/cast iron)  
body, cover with O-ring seal, threaded locking handles, and a  
strainer basket of perforated electro-polished stainless steel  
basket material.  
The recirculating pump shall be a self-priming, centrifugal design  
with a hair and lint strainer as shown in the plans.  
The pump body, seal plate, and attached hair and lint strainer shall  
be constructed of close-grained gray iron with fusion-bonded epoxy  
®
®
The strainer body shall be 6" ANSI 125 bolt flanged with fusion-  
coating of Scotchkote 134 on all wetted cast iron surfaces and  
®
bonded epoxy coating of Scotchkote on all wetted cast iron  
close-coupled to an electric motor by means of an adaptor of the  
same material. The pump body shall have a single suction port with  
surfaces unless specified for in-line mounting ahead of the pump.  
The strainer body shall have a removable drain plug for winterizing.  
®
a 6” ANSI 125 bolt flange to the hair and lint strainer. A centerline  
®
discharge port of 4” ANSI 125 bolt flange and a winterizing drain  
The strainer basket shall be securely positioned below the  
suction inlet of the trap, with access for inspection and cleaning  
through a removable trap body lid. The trap body lid shall be  
secured by means of threaded locking handles. The strainer  
basket shall have perforations which in total area is equal to  
6 times the open area of the suction pipe into the trap body inlet.  
1
port of 4” NPT shall be a part of the design.  
The pump shall be a back pull-out design to allow servicing with-  
out disturbing piping. The pump shall have a cast iron diffuser to  
aid in priming and it shall contain a replaceable bronze wear ring  
for the impeller. The impeller shall be of the closed type and cast  
in red brass, non-overloading at any point on the performance  
The pump strainer shall be Sta-Rite Model No. _______  
®
curve. The mechanical shaft seal shall be a John Crane type 21  
or equivalent and constructed of ceramic and carbon seal faces,  
with stainless steel, brass and Buna N materials in the spring  
bellows portion. The impeller shall be secured to the motor shaft  
by means of a stainless steel key and locking screw into the end  
of the motor shaft. There shall be a shaft slinger made of  
Phone: 800-831-7133  
Fax: 800-284-4151  
1/06 Part #P1-741  
©2006 Pentair Water Pool and Spa, Inc. All rights reserved.  
 

Philips Blu ray Player BDP3008 User Manual
Philips Electric Toothbrush HX5752 User Manual
Philips Flat Panel Television PT418APT A User Manual
Philips Laptop Docking Station DC291 User Manual
Philips Telephone Accessories SWL4160 User Manual
Philips TV VCR Combo 21PV320 User Manual
Pioneer DVD Recorder DE 7001 User Manual
Pioneer TV Receiver SC 07 User Manual
Pitney Bowes All in One Printer DA950 User Manual
Polaroid Digital Camera PDC 2000 User Manual