Pelco Security Camera c3401m a User Manual

I N S T A L L A T I O N  
Spectra® Mini Dome  
Indoor, Ceiling Mount  
C3401M-A (1/06)  
 
Important Safety Instructions  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.  
6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that  
produce heat.  
7. Only use attachments/accessories specified by the manufacturer.  
8. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is  
used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.  
9. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such  
as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has  
been exposed to rain or moisture, does not operate normally, or has been dropped.  
10. Installation should be done only by qualified personnel and conform to all local codes.  
11. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and  
it must not be installed where exposed to rain and moisture.  
12. Use only installation methods and materials capable of supporting four times the maximum specified load.  
13. Use stainless steel hardware to fasten the mount to outdoor surfaces.  
14. To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply sealant around the bolt holes  
between the mount and mounting surface.  
15. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not  
perform any servicing other that contained in the operating instructions unless you are qualified to do so.  
16. Only use replacement parts recommended by Pelco.  
The product and/or manual may bear the following marks:  
This symbol indicates that dangerous voltage constituting a risk of electric shock is  
present within this unit  
CAUTION:  
RISK OF ELECTRIC SHOCK.  
This symbol indicates that there are important operating and maintenance instructions  
DO NOT OPEN.  
in the literature accompanying this unit.  
C3401M-A (1/06)  
3
 
Regulatory Notices  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device  
may not cause harmful interference, and (2) this device must accept any interference received, including interference that  
may cause undesired operation.  
RADIO AND TELEVISION INTERFERENCE  
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the  
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal-  
lation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accor-  
dance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that  
the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct  
the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference  
Problems.” This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.  
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your  
authority to operate this equipment under Federal Communications Commission’s rules.  
This Class B digital apparatus complies with Canadian ICES-003.  
4
C3401M-A (1/06)  
 
Description  
The Spectra® Mini is an indoor dome system designed for ceiling applications. The dome can be mounted to the surface of  
ceilings, or it can be recessed in hard ceilings or standard 2 x 2 ft (61 x 61 cm) tiles in suspended ceilings. The Spectra Mini  
includes a high resolution color camera; video output capability through either coaxial cable or UTP wiring; pan/tilt control  
using D, P, or Coaxitron® protocol; and on-screen programming.  
A translator board can be installed on the dome for communication with non-Pelco controllers. The dome is compatible  
with the following translator boards:  
TXB-AD  
TXB-B  
Translator board for American Dynamics controllers  
Translator board for Philips (Burle) controllers  
Translator board for Sensormatic controllers  
Translator board for Vicon controllers  
TXB-S422  
TXB-V  
MODELS  
SD4-W0  
Indoor dome system, smoked bubble, NTSC  
Indoor dome system, clear bubble, NTSC  
Indoor dome system, smoked bubble, PAL  
Indoor dome system, clear bubble, PAL  
SD4-W1  
SD4-W0-X  
SD4-W1-X  
C3401M-A (1/06)  
5
 
Installation  
The following parts are supplied with the Spectra Mini dome system:  
Dome drive  
Dome bubble with trim ring  
1
1
1
1
2
2
1
1
1
Interface cable with a male RJ45-10 connector on one end and four twisted wire pairs on the other end  
Cover for use with optional translator board  
#10 x 1.50-inch self-tapping screws for suspended ceiling installation  
#8 x 3.50-inch self-tapping screws for surface mount installation  
Installation manual  
Operation/Programming manual  
Template  
The following parts, in addition to normal installation tools, are needed but not supplied:  
1
1
2
2
2
Small flashlight for viewing switches  
Long-handled flat-blade screwdriver for setting switches  
6-32 toggle bolts for surface mount installation  
8-32 studs and nuts for surface mount installation to concrete  
3-16 toggle bolts for recessed installation in hard ceiling  
DOME DRIVE  
TRIM RING AND  
BUBBLE  
TRANSLATOR BOARD  
COVER  
INTERFACE CABLE  
AND RJ45-10  
CONNECTOR  
MANUALS  
1.5-INCH SELF-TAPPING  
SCREWS, 2 EA.  
3.5-INCH SELF-TAPPING  
SCREWS, 2 EA.  
Figure 1. Package Components  
6
C3401M-A (1/06)  
 
SWITCH SETTINGS  
Coaxitron control: If you are going to use Coaxitron protocol to communicate with the dome system, you do not have to  
set any switches. Proceed to the installation instructions that follow this section.  
Non-Pelco control: If you are going to install a protocol translator board to communicate with the dome system through  
a non-Pelco controller, proceed to the installation instructions that follow this section. When you are instructed to install  
the translator board, you will set the switches as described in the installation/operation manual that accompanies the  
translator board.  
D or P control: If you are going to use D or P protocol to communicate with the dome system, follow the steps below to  
set the switches. Refer to Figure 2.  
WARNING: Do not remove the dome liner (refer to Figure 2). Replacing the dome liner requires qualified service  
personnel; otherwise, the dome drive may not operate properly.  
2. Point the camera straight up.  
3. Using a flashlight, look straight down through the viewing slot of the dome liner. Look at the circuit board in the  
bottom of the housing. Rotate the dome liner until you see two DIP switches on the circuit board.  
4. Set the switches. Refer to Table A, Table B, and Table C. There are no settings for SW1.  
NOTE: The unit automatically detects D or P protocal.  
DOME  
LINER  
ON  
SW 3  
ON  
SW 2  
REMOTE  
PORT  
Figure 2. Component Locations  
DATA PORT  
The data port (refer to Figure 2) allows access for on-site setup and testing of the dome system. It also is used for  
uploading revised operating software and language files. Refer to Software/Language File Upload in the Operation/  
Programming manual.  
C3401M-A (1/06)  
7
 
 
Table A. Switch Settings for SW2  
Special Systems  
Switch Number  
AD-32 Preset System  
CM9502 Setting  
Baud Rate  
SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 SW2-9  
ON  
ON  
Switch Number  
2400 Baud  
SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 SW2-9  
OFF  
ON  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
4800 Baud  
9600 Baud  
Protocol Termination  
Switch Number  
Terminated  
SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 SW2-9  
ON*  
Not Terminated  
OFF*  
*If you are connecting a single dome to a controller, terminate the dome. When connecting more than one dome to a single  
controller, terminate the dome farthest from the controller.  
Table B. Switch Settings for SW3 (P-Type Control)  
SWITCH SETTING  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SPECTRA  
ADDRESS  
SW3-1  
OFF  
ON  
SW3-2  
OFF  
OFF  
ON  
SW3-3  
OFF  
OFF  
OFF  
OFF  
ON  
SW3-4  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW3-5  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
SW3-1  
OFF  
ON  
SW3-2  
OFF  
OFF  
ON  
SW3-3  
OFF  
OFF  
OFF  
OFF  
ON  
SW3-4  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW3-5  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
1
2
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
3
OFF  
ON  
OFF  
ON  
4
ON  
ON  
5
OFF  
ON  
OFF  
OFF  
ON  
OFF  
ON  
OFF  
OFF  
ON  
6
ON  
ON  
7
OFF  
ON  
ON  
OFF  
ON  
ON  
8
ON  
ON  
ON  
ON  
9
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
10  
11  
12  
13  
14  
15  
16  
ON  
ON  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
8
C3401M-A (1/06)  
 
 
Table C. Switch Settings for SW3 (D-Type Control)  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW3-1  
ON  
SW3-2  
OFF  
ON  
SW3-3  
OFF  
OFF  
OFF  
ON  
SW3-4  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW3-5  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW3-6  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW3-7  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
SW3-8  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
1
2
OFF  
ON  
3
ON  
4
OFF  
ON  
OFF  
OFF  
ON  
5
ON  
6
OFF  
ON  
ON  
7
ON  
ON  
8
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
9
ON  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
C3401M-A (1/06)  
9
 
 
Table C. Switch Settings for SW3 (D-Type Control) (Continued)  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW3-1  
ON  
SW3-2  
ON  
SW3-3  
ON  
SW3-4  
OFF  
ON  
SW3-5  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW3-6  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
SW3-7  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW3-8  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
ON  
10  
C3401M-A (1/06)  
 
Table C. Switch Settings for SW3 (D-Type Control) (Continued)  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW3-1  
ON  
SW3-2  
OFF  
ON  
SW3-3  
ON  
SW3-4  
ON  
SW3-5  
OFF  
OFF  
OFF  
ON  
SW3-6  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW3-7  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
SW3-8  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
77  
78  
OFF  
ON  
ON  
ON  
79  
ON  
ON  
ON  
80  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
81  
ON  
82  
OFF  
ON  
ON  
83  
ON  
ON  
84  
OFF  
ON  
OFF  
OFF  
ON  
ON  
85  
ON  
ON  
86  
OFF  
ON  
ON  
ON  
87  
ON  
ON  
ON  
88  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
89  
ON  
ON  
90  
OFF  
ON  
ON  
ON  
91  
ON  
ON  
ON  
92  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
93  
ON  
ON  
ON  
94  
OFF  
ON  
ON  
ON  
ON  
95  
ON  
ON  
ON  
ON  
96  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
97  
ON  
98  
OFF  
ON  
ON  
99  
ON  
ON  
100  
101  
102  
103  
104  
105  
106  
107  
108  
109  
110  
111  
112  
113  
114  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
OFF  
ON  
ON  
C3401M-A (1/06)  
11  
 
Table C. Switch Settings for SW3 (D-Type Control) (Continued)  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW3-1  
ON  
SW3-2  
ON  
SW3-3  
OFF  
ON  
SW3-4  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW3-5  
ON  
SW3-6  
ON  
SW3-7  
ON  
SW3-8  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
115  
116  
117  
118  
119  
120  
121  
122  
123  
124  
125  
126  
127  
128  
129  
130  
131  
132  
133  
134  
135  
136  
137  
138  
139  
140  
141  
142  
143  
144  
145  
146  
147  
148  
149  
150  
151  
152  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
ON  
12  
C3401M-A (1/06)  
 
Table C. Switch Settings for SW3 (D-Type Control) (Continued)  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW3-1  
ON  
SW3-2  
OFF  
ON  
SW3-3  
OFF  
OFF  
OFF  
ON  
SW3-4  
ON  
SW3-5  
ON  
SW3-6  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
SW3-7  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
SW3-8  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
153  
154  
155  
156  
157  
158  
159  
160  
161  
162  
163  
164  
165  
166  
167  
168  
169  
170  
171  
172  
173  
174  
175  
176  
177  
178  
179  
180  
181  
182  
183  
184  
185  
186  
187  
188  
189  
190  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
C3401M-A (1/06)  
13  
 
Table C. Switch Settings for SW3 (D-Type Control) (Continued)  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW3-1  
ON  
SW3-2  
ON  
SW3-3  
ON  
SW3-4  
ON  
SW3-5  
ON  
SW3-6  
ON  
SW3-7  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
SW3-8  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
191  
192  
193  
194  
195  
196  
197  
198  
199  
200  
201  
202  
203  
204  
205  
206  
207  
208  
209  
210  
211  
212  
213  
214  
215  
216  
217  
218  
219  
220  
221  
222  
223  
224  
225  
226  
227  
228  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
14  
C3401M-A (1/06)  
 
Table C. Switch Settings for SW3 (D-Type Control) (Continued)  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW3-1  
ON  
SW3-2  
OFF  
ON  
SW3-3  
ON  
SW3-4  
OFF  
OFF  
OFF  
ON  
SW3-5  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW3-6  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
SW3-7  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
SW3-8  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
229  
230  
231  
232  
233  
234  
235  
236  
237  
238  
239  
240  
241  
242  
243  
244  
245  
246  
247  
248  
249  
250  
251  
252  
253  
254  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
C3401M-A (1/06)  
15  
 
SURFACE MOUNT INSTALLATION  
1. On top of the dome drive is an opening for an optional translator board. The opening has a cover that must be left in  
If you are going to install a translator board, follow the instructions that come with the translator board.  
If you are not going to install a translator board, save the taller cover in case a translator board is ever installed.  
2. Prepare the ceiling as follows:  
b. Dome with translator board: Punch out the pie-shaped section from the supplied templates. Using the pie-  
shaped template, either cut a hole through the ceiling or make a hole with a depth of 0.25 inches (6 mm).  
the wires to the ceiling and then run the wires through the air gap between the ceiling and the surface mount  
ring as shown in Figure 5.  
3. Connect the wiring and attach the dome drive to the ceiling.  
You can plug the male RJ45-10 connector (also known as an RJ-50 connector) on the supplied interface cable (refer  
to Figure 6) into the mating connector on top of the dome drive and then connect your wiring to the other end of the  
cable.  
Or  
WARNING: Do not over-tighten the mounting hardware. Doing so can impede the pan movement of the  
dome drive.  
Refer to Figure 3 and Figure 4 for installing the dome drive.  
Refer to Figure 6, Table D, Table E, and Table F for wiring connections. Note that you can connect video using either  
an unshielded twisted pair (UTP) of wires (refer to Table D) or coaxial cable (refer to Table E.) A BNC connector for  
coaxial cable is attached to the dome drive.  
If you are wiring more than one dome drive to the same transformer, connect one side of the transformer to pin 9 of  
the RJ45-10 connector on all modules. Connect the other side of the transformer to pin 10 of the RJ45-10 connector  
on all modules. Failure to connect all modules the same way will cause the cameras to be out of phase with each  
other and may produce a vertical roll when switching between cameras.  
4. Line up the tabs on the trim ring with the slots in the dome drive. Snap the trim ring and bubble into place.  
16  
C3401M-A (1/06)  
 
CONCRETE  
CEILING  
CEILING  
6-32 TOGGLE BOLTS  
(NOT SUPPLIED)  
OR  
#8 X 3.5-INCH  
SELF-TAPPING  
SCREWS  
8-32 MOUNTING  
HARDWARE  
(NOT SUPPLIED)  
(SUPPLIED)  
DOME DRIVE  
DOME DRIVE  
Figure 3. Ceiling Installation  
Figure 4. Concrete Ceiling Installation  
MALE RJ45-10  
CONNECTOR  
TWISTED PAIRS  
Figure 5. Wiring Attached to Ceiling  
Figure 6. Interface Cable  
C3401M-A (1/06)  
17  
 
       
Table D. Interface Cable Wiring  
Table E. Video Coaxial Cable Requirements  
Pin Color  
Function  
UTP-  
UTP+  
RX-  
Cable Type*  
RG59/U  
Maximum Distance  
750 ft (229 m)  
1
2
3
4
5
6
7
8
9
ORANGE  
RG6/U  
1,000 ft (305 m)  
1,500 ft (457 m)  
WHITE/ORANGE  
GREEN  
RG11/U  
WHITE/GREEN  
BLUE  
RX+  
*Cable requirements:  
75-ohm impedance  
TX-  
All-copper center conductor  
All-copper braided shield with 95% braid coverage  
WHITE/BLUE  
NOT USED  
NOT USED  
BROWN  
TX+  
24 V  
24 V  
10 WHITE/BROWN  
Table F. Wiring Distances  
The following are the recommended maximum distances for 24 VAC applications and are calculated with a 10 percent  
voltage drop. (Ten percent is generally the maximum allowable voltage drop for AC-powered devices.  
Wire Gauge  
Voltage  
18  
16  
14  
12  
(1.0 mm2)  
(1.5 mm2)  
(2.5 mm2)  
(3.5 mm2)  
215 ft  
(97 m)  
341 ft  
(154 m)  
542 ft  
(245 m)  
863 ft  
(391 m)  
24 VAC  
NOTE: Power consumption is 21 VA per unit. Use a power source with a minimum of 21 VA per unit.  
18  
C3401M-A (1/06)  
 
 
RECESSED INSTALLATION  
SUSPENDED CEILING  
1. On top of the dome drive is an opening for an optional translator board. The opening has a cover that must be left in  
place if a translator board is not required. A taller cover is supplied if a translator board is installed.  
If you are not going to install a translator board, save the taller cover in case a translator board is ever installed.  
2. Remove the ceiling tile from the ceiling.  
3. Using the supplied template, cut holes in the ceiling tile for the dome drive and mounting hardware.  
4. Remove the surface mount ring from the dome drive as follows. Refer to Figure 7.  
a. Place fingers on the circular marks located on the sides of the surface mount ring.  
b. Pinch the sides.  
c. Lift and remove the surface mount ring from the dome drive. Do not discard the surface mount ring because it is  
5. Connect the wiring and attach the dome drive to the ceiling tile.  
Using the supplied interface cable:  
a. Plug the male RJ45-10 connector (also known as an RJ-50 connector) on the supplied interface cable (refer to  
Figure 6) into the mating connector on top of the dome drive.  
b. Turn the surface ring upside down, and place it on the inside of the ceiling tile. Refer to Figure 8.  
WARNING: Do not over-tighten the mounting hardware. Doing so can impede the pan movement of the  
dome drive.  
screws (supplied). Refer to Figure 8.  
d. Replace the ceiling tile.  
e. Remove an adjacent ceiling tile, and connect your wiring to the dome drive.  
Refer to Figure 6, Table D, Table E, and Table F for wiring connections. Note that you can connect video using  
either an unshielded twisted pair (UTP) of wires (refer to Table D) or coaxial cable (refer to Table E.) A BNC  
connector for coaxial cable is attached to the dome drive.  
If you are wiring more than one dome drive to the same transformer, connect one side of the transformer to pin  
9 of the RJ45-10 connector on all modules. Connect the other side of the transformer to pin 10 of the RJ45-10  
connector on all modules. Failure to connect all modules the same way will cause the cameras to be out of  
phase with each other and may produce a vertical roll when switching between cameras.  
C3401M-A (1/06)  
19  
 
Using the supplied RJ45-10 connector:  
a. Connect the supplied RJ45-10 connector to your wiring and then plug the connector into the dome drive.  
Refer to Figure 6, Table D, Table E, and Table F for wiring connections. Note that you can connect video using  
either an unshielded twisted pair (UTP) of wires (refer to Table D) or coaxial cable (refer to Table E.) A BNC  
connector for coaxial cable is attached to the dome drive.  
If you are wiring more than one dome drive to the same transformer, connect one side of the transformer to pin  
9 of the RJ45-10 connector on all modules. Connect the other side of the transformer to pin 10 of the RJ45-10  
connector on all modules. Failure to connect all modules the same way will cause the cameras to be out of  
phase with each other and may produce a vertical roll when switching between cameras.  
b. Turn the surface ring upside down, and place it on the inside of the ceiling tile. Refer to Figure 8.  
WARNING: Do not over-tighten the mounting hardware. Doing so can impede the pan movement of the dome drive.  
c. Attach the dome drive to the ceiling tile and surface mount ring with the two #10 x 1.50-inch self-tapping  
screws (supplied). Refer to Figure 8.  
d. Replace the ceiling tile.  
DOME DRIVE  
SURFACE  
MOUNT RING  
Figure 7. How to Remove Surface Mount Ring  
20  
C3401M-A (1/06)  
 
 
SURFACE MOUNT RING  
CEILING  
TILE  
DOME DRIVE  
#10 x 1.50-INCH  
SELF-TAPPING  
SCREWS  
(SUPPLIED)  
Figure 8. Ceiling Tile Installation  
6. Line up the tabs on the trim ring with the slots in the dome drive. Snap the trim ring and dome bubble into place.  
C3401M-A (1/06)  
21  
 
 
HARD CEILING  
1. On top of the dome drive is an opening for an optional translator board. The opening has a cover that must be left in  
place if a translator board is not required. A taller cover is supplied if a translator board is installed.  
If you are not going to install a translator board, save the taller cover in case a translator board is ever installed.  
2. Using the supplied template, cut holes in the ceiling for the dome drive and mounting hardware. Pull the wiring for  
power, video, and control through the ceiling.  
3. Remove the surface mount ring from the dome drive as follows. Refer to Figure 7.  
a. Place fingers on the circular marks located on the sides of the surface mount ring.  
b. Pinch the sides.  
c. Lift and remove the surface mount ring from the dome drive.  
4. Connect the wiring.  
You can plug the male RJ45-10 connector (also known as an RJ-50 connector) on the supplied interface cable (refer  
cable.  
Or  
You can connect the supplied RJ45-10 connector to your wiring and then plug the connector into the dome drive.  
Refer to Figure 6, Table D, Table E, and Table F for wiring connections. Note that you can connect video using either  
an unshielded twisted pair (UTP) of wires (refer to Table D) or coaxial cable (refer to Table E.) A BNC connector for  
coaxial cable is attached to the dome drive.  
If you are wiring more than one dome drive to the same transformer, connect one side of the transformer to pin 9 of  
the RJ45-10 connector on all modules. Connect the other side of the transformer to pin 10 of the RJ45-10 connector  
on all modules. Failure to connect all modules the same way will cause the cameras to be out of phase with each  
other and may produce a vertical roll when switching between cameras.  
22  
C3401M-A (1/06)  
 
WARNING: Do not over-tighten the mounting hardware. Doing so can impede the pan movement of the dome drive.  
5. Attach the dome drive to the ceiling with the two 3-16 toggle bolts (not supplied). Refer to Figure 9.  
DOME DRIVE  
CEILING  
3-16 TOGGLE BOLTS  
(NOT SUPPLIED)  
Figure 9. In-Ceiling Installation to a Fixed Ceiling  
6. Line up the tabs on the trim ring with the slots in the dome drive. Snap the trim ring and bubble into place.  
C3401M-A (1/06)  
23  
 
 
Specifications  
MECHANICAL  
Pan Movement  
Vertical Tilt  
360° continuous pan rotation  
Unobstructed +2° to -92°  
Manual Pan/Tilt Speeds  
Pan  
Tilt  
0.4-80°/sec manual operation, 100°/sec turbo  
0.7-40°/sec manual operation  
Preset Speeds  
Pan  
Tilt  
140°/sec  
80°/sec  
For variable speed operation an appropriate controller is required.  
ELECTRICAL  
Input Voltage  
Input Power  
Fuse  
18-30 VAC, 24 VAC nominal  
21 VA nominal  
1.6 A  
GENERAL  
Construction  
Top Cap  
Anodized cast aluminum  
Trim Ring and  
Surface Mount Ring  
Bubble  
ABS plastic  
Acrylic  
Finish  
White  
Light Attenuation  
Smoked  
Clear  
1/2 F-stop light loss  
Zero light loss  
Cable Entry  
Single RJ45-10 connector, pigtail supplied  
BNC connector  
Environment  
Weight  
Indoor  
1.75 lb (0.79 kg)  
CAMERA  
Signal Format  
Scanning System  
Image Sensor  
NTSC/PAL  
2:1 interlace  
1/4-inch interline CCD  
Effective Pixels  
NTSC  
PAL  
768 (H) x 494 (V)  
752 (H) x 582 (V)  
24  
C3401M-A (1/06)  
 
Horizontal Resolution  
NTSC  
PAL  
>470 TV lines  
>460 TV lines  
Minimum Illumination  
Sync System  
3.0 lux  
AC line lock, phase adjustable via remote control, V-Sync  
Automatic with manual override  
White Balance  
Shutter Speed  
Automatic (electronic iris)/manual  
1/60~1/30,000  
Gain Control  
Automatic with manual override  
1.0 to 1.2 Vp-p, 75 ohms, adjustable  
>50 dB  
Video Output  
Video Signal-to-Noise Ratio  
LENS  
Lens  
F1.8 (F=4.2-42 mm optical) 10X optical zoom, 8X digital zoom  
1.5/2.5/4.3 seconds  
Zoom Speed (optical range)  
Horizontal Angle of View  
46.4° wide zoom  
5.0° telephoto zoom  
Focus  
Automatic with manual override  
Automatic with manual override  
Iris Control  
(Design and product specifications subject to change without notice.)  
WITH TXB TRANSLATOR BOARD  
WITHOUT TXB TRANSLATOR BOARD  
5.05  
(12.83)  
5.05  
(12.83)  
Ø6.19  
(15.72)  
Ø6.19  
(15.72)  
5.13  
(13.03)  
5.27  
(13.39)  
Ø4.25  
(10.80)  
Ø4.25  
(10.80)  
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.  
C3401M-A (1/06)  
25  
 
26  
C3401M-A (1/06)  
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.  
Exceptions to this warranty are as noted below:  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which  
have a five-year warranty.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
Two years (except lamp and color wheel) on Digital Light Processing (DLP ®) displays. The lamp and color wheel will be covered for a period of 90 days. The air filter  
is not covered under warranty.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, Endura Series distributed network-based video products, and TW3000  
Series twisted pair transmission products.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco,  
Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any  
claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price  
paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit  
and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product  
when returned.  
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number  
if returned for credit, and RA number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following :  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
REVISION HISTORY  
Manual #  
C3401M  
C3401M-A  
Date Comments  
12/05 Original version.  
1/06 Added warning about over-tightening mounting hardware.  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
DLP is a registered trademark of Texas Instruments, Inc.  
©Copyright 2006, Pelco. All rights reserved.  
 
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East  
|
|
|
|
|
|
|
|
 

Philips DVD VCR Combo DVP3345V User Manual
Philips Refrigerator 32PFL7482 User Manual
Pioneer Blu ray Player BDP LX08 User Manual
Pioneer Stereo System VSX 816 K User Manual
Plantronics Bluetooth Headset Plantronics Explorer 210 Series User Manual
Polaris Offroad Vehicle X2 500 EFI User Manual
Porter Cable Satellite TV System DSR2210 User Manual
Poulan Trimmer TE450 User Manual
Powermate Portable Generator PM0435004 User Manual
Precor Cell Phone Accessories P80 CONSOLE User Manual