Pelco Home Security System C718M User Manual

®
IOP19 Series  
Integral Color Camera/Lens for  
SB1900 Series Dome  
Installation/Operation Manual  
C718M (10/96)  
Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • (1-209) 292-1981 • (800) 289-9100  
FAX (800) 289-9150 or (1-209) 292-3827  
 
TABLE OF CONTENTS  
Section  
Page  
1.0 WARNINGS ........................................................................................................................................1  
2.0 SCOPE ...............................................................................................................................................2  
3.0 DESCRIPTION ...................................................................................................................................2  
3.1 MODELS ..................................................................................................................................2  
4.0 INSTALLATION ..................................................................................................................................2  
5.0 ADJUSTMENTS .................................................................................................................................4  
5.1 BACK FOCUS ..........................................................................................................................4  
5.2 SHUTTER SPEED....................................................................................................................5  
5.3 AUTO GAIN CONTROL ...........................................................................................................5  
5.4 WHITE BALANCE (ATW/AWB SWITCH) .................................................................................6  
5.5 V-PHASE (VERTICAL PHASE) ................................................................................................6  
6.0 WIRING DIAGRAM ............................................................................................................................7  
7.0 EXPLODED ASSEMBLY DRAWING - TVH6 .....................................................................................8  
7.1 MECHANICAL PARTS LIST .....................................................................................................8  
8.0 EXPLODED ASSEMBLY DRAWING - TVH10 ...................................................................................9  
8.1 MECHANICAL PARTS LIST .....................................................................................................9  
9.0 SPECIFICATIONS............................................................................................................................10  
10.0 WARRANTY AND RETURN INFORMATION................................................................................... 11  
®Pelco and the Pelco logo are registered trademarks of Pelco.  
©Copyright 1996, Pelco. All rights reserved.  
ii  
PELCO Manual C718M (10/95)  
 
LIST OF ILLUSTRATIONS  
Figure  
Page  
1
2
3
4
5
6
7
8
9
IOP Package Installation..............................................................................................................2  
Wiring Diagram for SB1900 Dome and IOP Package .................................................................3  
Back Focus Adjustment ...............................................................................................................4  
Camera Adjustments ...................................................................................................................5  
Wiring Diagram for Color Camera/Lens.......................................................................................7  
TVH6 Camera/Lens Combination Exploded Assembly Drawing .................................................8  
TVH10 Camera/Lens Combination Exploded Assembly Drawing ...............................................9  
TVH6 Camera Dimensions ........................................................................................................10  
TVH10 Camera Dimensions ......................................................................................................10  
REVISION HISTORY  
Manual #  
Date  
Comments  
C718M  
10/96  
Original manual.  
PELCO Manual C718M (10/96)  
iii  
 
IOP19 SERIES INTEGRAL  
COLOR CAMERA/LENS PACKAGE  
FOR SB1900 SERIES DOMES  
1.0 WARNINGS  
3. Only use replacement parts recommended by  
Pelco.  
Prior to installation and use of this product, the follow-  
ing WARNINGS should be observed.  
4. After replacement/repair of this unit’s electrical  
components, conduct a resistance measurement  
between line and exposed parts to verify the ex-  
posed parts have not been connected to line cir-  
cuitry.  
1. Installation and servicing should only be done by  
Qualified Service Personnel and conform to all  
Local codes.  
2. Unless the unit is specifically marked as a NEMA  
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is de-  
signed for indoor use only and it must not be in-  
stalled where exposed to rain and moisture.  
Theproductmaybearthefollowingmarks:  
This symbol indicates that dangerous voltage  
constituting a risk of electric shock is present  
within this unit.  
This symbol indicates that there are important  
operating and maintenance instructions in the  
literature accompanying this unit.  
CAUTION:  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
CAUTION:  
TOREDUCETHERISKOFELECTRICAL  
SHOCK, DO NOT REMOVE COVER. NO  
USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL.  
Please thoroughly familiarize yourself with the information in this manual  
prior to installation and operation.  
Pelco Manual C718M (10/96)  
1
 
4.0 INSTALLATION  
2.0 SCOPE  
To install the camera/lens package in your dome, fol-  
low the steps below.  
This manual covers the IOP19 Series of integral color  
camera/lens packages.  
1. Disconnect main power to the back box.  
2. Remove the dome drive from the back box.  
3.0 DESCRIPTION  
Pelco's IOP19 Series of integral color camera/lens com-  
binations are specifically designed for use in the SB1900  
Series of indoor surveillance dome enclosures.  
3. Refer to Figure 1. Remove the nuts and flat wash-  
ers from the 1/4-20 studs on the bottom of the IOP  
package. Insert the studs through the slots in the  
tilt table. Make sure the lens is facing the front of  
the tilt table.Attach the IOPpackage to the tilt table  
with the washers and nuts. Tighten the nuts just  
snug.  
Design considerations were engineered into this series  
of integral camera/lens combinations to ensure ease of  
servicing.  
3.1 MODELS  
4. Refer to Figure 2 and make the electrical connec-  
tions.  
The following cameras with integral lens are for use in  
SB1900 series domes:  
5. Insert the dome drive into the back box. Adjust the  
IOP package on the tilt table so that it is as close to  
the dome as possible without hitting the dome when  
the IOPpackage is tilted up or down. Then securely  
tighten the nuts on the IOP package.  
IOP19C3B  
IOP19C3G  
Basic color NTSC (EIA) series camera  
with integral TVH6M-1 lens  
Basic color NTSC (EIA) series camera  
with integral TVH10M-1 lens  
Figure 1. IOP Package Installation  
2
Pelco Manual C718M (10/96)  
 
Figure 2. Wiring Diagram for SB1900 Dome and IOP Package  
Pelco Manual C718M (10/96)  
3
 
White Balance  
5.0 ADJUSTMENTS  
White balance has two positions; one isATW (Au-  
tomatic Tracing White), which is a feature that  
continuously adjusts the camera for optimum color  
reproduction. AWB (Automatic White Balance) is  
a feature that retains current settings in memory  
even when the power is off.  
Your optics package comes from the factory adjusted  
for a broad range of lighting conditions. For this rea-  
son, you may find it necessary to adjust your optics  
package to tailor the picture to your specific viewing  
environment. The following adjustments can be made  
to the optics package:  
V-Phase (Vertical Phase)  
Synchronizes the picture when multiple optics  
packages are used in a system.  
Back focus  
Shutter speed  
AGC  
White balance  
V-phase (vertical phase)  
The location for the controls of the above features, ex-  
cept for back focusing, are shown in Figure 4. The back  
focus adjustment location is shown in Figure 3. The  
following sections define the above features and specify  
how to adjust them to gain the best system performance  
in your environment.  
The factory adjustments for the above controls are set  
as follows:  
Back Focus  
5.1 BACK FOCUS  
Adjusted with the camera looking at an object 55  
feet (16.76 m) from the lens. The results are a clear,  
in-focus picture through the entire zoom range.  
Back focusing involves controlling the distance between  
the focal point of the lens and the image head. If the  
lens is focused on the imaging head properly, a clear  
picture is maintained through the entire zoom range.  
Shutter Speed  
Factory set to the slowest speed available: 1/60  
second.  
The optics package has been back focused at the fac-  
tory.  
Auto Gain Control  
AGC ON/OFF set to ON.  
In some cases, additional back focusing may be re-  
quired. Should this be the case, adjust the back focus  
by moving the lens positions to zoom wide and focus  
far. Then position the camera on an object with clean  
lines such as a window seal, shelf, etc., at a minimum  
distance of 55 feet (16.76 m).  
The back focus adjustment screw location is shown in  
Figure 3. Use a small, standard, straight-slotted screw-  
driver to adjust the screw, which is recessed in the cam-  
era housing. The mechanical movement of the screw  
as the screwdriver is turned is about three clicks (or  
detents) in either direction.  
As you move the back focus set screw back and forth,  
the distance between the lens and image head moves in  
and out. You will be able to see the clean line come in  
and out of focus. Continue to adjust the screw back and  
forth until the optimum focus is obtained.  
Figure 3. Back Focus Adjustment  
4
Pelco Manual C718M (10/96)  
 
5.2 SHUTTER SPEED  
5.3 AUTO GAIN CONTROL  
This optics package is provided with adjustable shutter  
speeds. This feature allows minimal streaking when a  
very fast moving object passes in front of the non-  
moving optics package. The shutter speed is factory  
set to 1/60 second. You can select one of eight shutter  
speeds (refer to Figure 4).  
Refer to Figure 4. The AGC control setting should be  
set and left in the ON position.  
SHUTTER SPEED  
ADJUSTMENTS MAY BE  
PERFORMED BY USING  
A SMALL STANDARD  
SCREWDRIVER  
V-PHASE BUTTONS (MOMENTARY  
PUSH-BUTTON) ADVANCE AND  
RETARD THE PHASE INTERVAL  
WITH RESPECT TO ZERO  
AND MOVING THE  
ROTARY SWITCH AS  
SHOWN. “0” POSITION  
IS FACTORY DEFAULT.  
SEE BELOW FOR  
CROSSOVER OF AC LINE ±90°  
SETTING VALUES  
THIS MOMENTARY  
BUTTON LOCKS AWB  
AGC (AUTOMATIC  
GAIN CONTROL) IS  
SET IN THE ON  
POSITION (SHOWN)  
SHUTTER POSITION  
SHUTTER SPEED  
(IN SECONDS)  
0
1
2
3
4
5
6
7
8
9
1/60  
1/100  
1/250  
1/500  
1/1000  
1/2000  
1/4000  
1/10,000  
NOT USED  
NOT USED  
Figure 4. Camera Adjustments  
Pelco Manual C718M (10/96)  
5
 
5.4 WHITE BALANCE (ATW/AWB SWITCH)  
In the ATW (Automatic Tracing White Balance) posi-  
tion, the white balance is continuously adjusted to take  
into account variations in the incident light conditions.  
In theAWB (Automatic White Balance) position, when  
the LOCK button is pressed, the white balance is auto-  
matically adjusted, and the setting is stored in memory.  
When the switch is set to this position the white bal-  
ance always takes the previously stored value.  
White balance is factory set to theAWB position and it  
is recommended that the optics package be used in this  
mode. Refer to Figure 4.  
5.5 V-PHASE (VERTICAL PHASE)  
V-phase (vertical phase) is valuable when multiple op-  
tic packages are switched by a sequential or matrix  
switcher. The vertical phase +/- buttons are used to com-  
pensate for vertical phase discrepancies that will occur  
in a multiple camera environment. In this type of envi-  
ronment, each camera's output is synchronized by the  
frequency of the power supply and phase.  
Two persons are required to synchronize the picture:  
one person at the optics package location and another  
at the control room looking at a monitor viewing switch-  
ing video signals from the optics packages.  
The V-phase adjustment is ±90°. Use the tip of a  
ballpoint pen or similar instrument to press the recessed  
+/- buttons (refer to Figure 4). The phase change is lin-  
ear. Pressing a button will activate a phase change in  
the direction indicated. The phase change will begin  
after about 1/2 second, but the switch must be held down  
for a total of 5 or 6 seconds for the phase change to  
occur. An equal amount of time is required to go in the  
opposite direction.  
Each optics package should be adjusted so that as the  
switchers switch from one optics package to the next,  
the monitor does not “roll” or show partial frames of  
the video picture.  
6
Pelco Manual C718M (10/96)  
 
6.0 WIRING DIAGRAM  
Figure 5. Wiring Diagram for Color Camera/Lens  
Pelco Manual C718M (10/96)  
7
 
7.0 EXPLODED ASSEMBLY DRAWING—TVH6  
Figure 6. TVH6 Camera/Lens Combination Exploded Assembly Drawing  
7.1 MECHANICAL PARTS LIST (Figure 6)  
Item  
Qty  
Description  
Part Number  
H6Z851M  
1
2
3
1
1
Lens, 1/2", 6X motorized zoom, F1.2, 8.5-51 mm  
Frame, 6X lens package  
Not used  
JIOP084307COMP  
4
1
1
1
1
1
Clamp, wire fatigue  
80010016  
5
Top cover  
JIOP084106COMP  
JIOP084108COMP  
SC-CPL27  
6
7
8
Back cover  
Camera, Sony, 1/2", high resolution, color (NTSC)  
Circuit board, IOP camera interconnect  
Not used  
Screw, 1/4-20 x .375" flat head, Phillips  
Screw, 2-56 x 1/2", pan head, Phillips  
Internal star washer, #2  
Screw, 2-56 x 3/8", pan head, Phillips  
Screw, 4-40 x 1/4" pan head, Phillips  
Nut, 2-56  
PCB8500200ASSY  
A
B
C
D
E
F
G
H
J
1
2
5
5
16  
2
ZH1/4-20X.375SP  
ZH2-56X.500SPS  
ZH2LWSIS  
ZH2-56X.375SRS  
ZH4-40X.250BPP  
ZH2-56NUTSH  
ZH2-56X.187SPS  
SPA9161  
2
Screw, 2-56 x 3/16" pan head, Phillips  
Spacer, 3/16" x .187"  
Spacer, 3/16" x .125"  
2
K
5
SPA9160  
8
Pelco Manual C718M (10/96)  
 
8.0 EXPLODED ASSEMBLY DRAWING—TVH10  
Figure 7. TVH10 Camera/Lens Combination Exploded Assembly Drawing  
8.1 MECHANICAL PARTS LIST (Figure 7)  
Item  
Qty  
Description  
Part Number  
1
2
1
1
Lens, 1/2", 10X motorized zoom, F1.2, 8-80 mm  
Frame, 10X lens package  
Not used  
H10Z880M  
JIOP194504COMP  
3
4
1
1
1
1
1
Clamp, wire fatigue  
80010016  
5
Top cover  
Back cover  
JIOP084103COMP  
JIOP084105COMP  
SC-CPL27  
6
7
Camera, Sony, 1/2", high resolution, color (NTSC)  
Circuit board, IOP camera interconnect  
Not used  
Screw, 1/4-20 x .375" flat head, Phillips  
Screw, 2-56 x 1/2", pan head, Phillips  
Internal star washer, #2  
Screw, 2-56 x 3/8", pan head, Phillips  
Screw, 4-40 x 1/4" pan head, Phillips  
Nut, 2-56  
Screw, 2-56 x 3/16" pan head, Phillips  
Spacer, 3/16" x .187"  
8
PCB8500200ASSY  
A
B
C
D
E
F
G
H
J
1
2
5
5
13  
2
2
2
ZH1/4-20X.375SP  
ZH2-56X.500SPS  
ZH2LWSIS  
ZH2-56X.375SRS  
ZH4-40X.250BPP  
ZH2-56NUTSH  
ZH2-56X.187SPS  
SPA9161  
K
5
Spacer, 3/16" x .125"  
SPA9160  
Pelco Manual C718M (10/96)  
9
 
9.0 SPECIFICATIONS  
MECHANICAL  
ELECTRICAL  
Color NTSC (EIA) Camera Module  
Mounting Bracket  
Input Voltage:  
24 VAC, 60 Hz  
Construction:  
Dimensions:  
0.050" aluminum  
See Figures 8 and 9  
Power  
Requirements:  
Less than 5 watts  
Video Output:  
1 V p–p composite video into 75  
ohms  
Operating  
Temperature:  
14° to 131°F (-10° to 55°C)  
Imaging Device: 1/2" CCD  
Illumination:  
2.5 LUX @ F1.2  
Scanning System: 525 lines, interlaced/60 Hz  
Horizontal  
Resolution:  
470 TVL  
Shutter Speed:  
Adjustable, 1/60 to 1/10,000  
second, 8 steps  
Automatic Gain  
Control:  
Present in auto mode only  
Figure 8. TVH6 Camera Dimensions  
Figure 9. TVH10 Camera Dimensions  
10  
Pelco Manual C718M (10/96)  
 
10.0 WARRANTY AND RETURN  
INFORMATION  
WARRANTY  
RETURNS  
Pelco will repair or replace, without charge, any merchandise proved  
defectiveinmaterialorworkmanshipforaperiodofoneyearafterthedate  
of shipment.  
In order to expedite parts returned to the factory for repair or credit, please  
call the factory at (800) 289-9100 or (559) 292-1981 to obtain an  
authorization number (CA number if returned for credit, and RA number  
if returned for repair).  
Exceptions to this warranty are as noted below:  
All merchandise returned for credit may be subject to a 20% restocking  
and refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the  
assigned CA or RA number and freight should be prepaid. Ship to the  
appropriate address below.  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and  
keyboard).  
Three years on Camclosure® and fixed camera models, except the  
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,  
and MC3651H-2X camera models, which have a five-year warranty.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto  
Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto  
Rico and are instructed to return goods to the USA, you may do one of the  
following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and  
DF5/DF8 Series fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, includ-  
ing when used in continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding  
wiper blades).  
Eighteen months on DX Series digital video recorders, NVR300  
Series network video recorders, and EnduraSeries distributed  
network-based video products.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
One year (except video heads) on video cassette recorders (VCRs).  
Video heads will be covered for a period of six months.  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods  
to:  
Six months on all pan and tilts, scanners or preset lenses used in  
continuousmotionapplications(thatis,presetscan,tourandautoscan  
modes).  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
Pelco will warrant all replacement parts and repairs for 90 days from the  
date of Pelco shipment. All goods requiring warranty repair shall be sent  
freight prepaid to Pelco, Clovis, California. Repairs made necessary by  
reason of misuse, alteration, normal wear, or accident are not covered  
under this warranty.  
Pelco assumes no risk and shall be subject to no liability for damages or  
loss resulting from the specific use or application made of the Products.  
Pelco’s liability for any claim, whether based on breach of contract,  
negligence, infringement of any rights of any party or product liability,  
relating to the Products shall not exceed the price paid by the Dealer to  
Pelco for such Products. In no event will Pelco be liable for any special,  
incidental or consequential damages (including loss of use, loss of profit  
and claims of third parties) however caused, whether by the negligence  
of Pelco or otherwise.  
The above warranty provides the Dealer with specific legal rights. The  
Dealer may also have additional rights, which are subject to variation from  
state to state.  
Ifawarrantyrepairisrequired,theDealermustcontactPelcoat(800) 289-  
9100 or (559) 292-1981 to obtain a Repair Authorization number (RA),  
and provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice  
number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product which does not fall  
under the warranty conditions stated above, please include a written  
explanation with the product when returned.  
Method of return shipment shall be the same or equal to the method by  
which the item was received by Pelco.  
Pelco, the Pelco logo, Camclosure, Esprit,  
Genex, Legacy, and Spectra are registered  
trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
© Copyright 1999, Pelco. All rights reserved.  
Pelco Manual C718M (10/96)  
11  
 
Pelco  
300 West Pontiac Way  
Clovis, CA 93612-5699  
(209) 292-1981 • (800) 289-9100  
FAX (800) 289-9150 or (209) 292-3827 • DataFAX (800) 289-9108 or (209) 292-0435  
International customers call 1-209-292-1981 or FAX 1-209-348-1120  
(Product specifications subject to change without notice.)  
C718M  
 

Peavey Musical Instrument Amplifier DataBass User Manual
Pelco Security Camera BB5L User Manual
Philips Computer Monitor 107S9 User Manual
Philips Projection Television 55P 9161 User Manual
Philips Video Gaming Accessories SCB5055 12 User Manual
Pioneer Stereo Receiver SC 67 User Manual
Pioneer Stereo System DRM 1004V40 User Manual
PMC Sierra Switch Gigabit Ethernet Switch User Manual
Pride Mobility Mobility Aid PMV520CRED User Manual
ProForm Exercise Bike 831215211 User Manual